Areas of application
→ Intended use Surfaces:
- Existing tiles
- Waterproofing products
- Cement-based screeds
- Concrete substrates
- Plasterboard
- Fibro-cement slabs
- Brick/blockwork
- Lime and cement-based plasters/renders
- Thermal insulation panelling systems
- Insulating panels
- Impact noise insulation sheets Materials:
- Porcelain tiles
- Laminated stoneware
- Low thickness slabs
- Ceramic tiles
- Large size
→ Marble natural stone
- Recomposed materials
- Glass mosaics
- Glass tiles
- Thermal and acoustic insulation
- Terracotta - klinker
→ Uses:
- Adhesive and finishing
- Floors and walls
- For internal use - external
- Overlaying
- Terraces and balconies
- Facades
- Swimming pools and fountains
- Saunas and spa
- Domestic
- Commercial
- Industrial
Instructions for use
→ Preparation of the surface
All surfaces must be dimensionally stable according to IS 1443-2018, level, cured, undamaged, compact, rigid, resistant, dry and I free from any debonding agents and from damp rising. It is good practice to dampen highly absorbent concrete surfaces or apply a coat of Primer A Eco.
→ Preparation
Mixing water on-site For low thickness fixing and full wettability: 7.0-8.5 litres of clean water per bag The amount of water to be added, indicated on the packaging, is an approximate guide. It is possible to obtain mixtures with a more or less non-sag consistency, depending on the type of application.
→ Application
To guarantee structural adhesion it is necessary to apply a layer of adhesive su cient to cover the entire back of the coating material.Large, rectangular sizes with sides > 60 cm and low thickness sheets may require adhesive to be applied directly to the back of the material. Check samples to make sure the adhesive has been transferred to the back of the material.
Create elastic expansion joints:
-= 10 m² in external applications
-= 25 m² in internal applications
- every 8 metres in long, narrow applications.
Respect all structural, fractionizing, and perimeter joints present in the surfaces.
TDS
Tensil Strength
(a) Dry Condition (MIN)N/MM2 - 1.5
(B) Wet Condition(MIM)N/MM2 - 1.42
Shear Adhesion Strength
(a) Dry Condition (MIM)M/MM2 - 1.5
(B) Wet Condition (MIM)M/MM2 - 1.2
(C) Heat Aging (MIM)M/MM - 1.2
Slip Test - 0.03mm
Dformablitiy S1 - > 3.6
| Adhesive thickness |
up to 15 mm |
| Temperature of the air, substrates and materials |
from +5 °C to +35 °C |
| Pot life at +23 °C |
- |
| Grey |
~3 hrs |
| White |
~3 hrs |
| Pot life at +35 °C (BIII tile): |
- |
| Grey |
~1.5 hrs |
| White |
~1.5 hrs |
| Open time at +23 °C (BIII tile): |
- |
| Grey |
≤ 60 min. |
| White |
≤ 60 min. |
| Open time at +35 °C (BIII tile): |
- |
| Grey |
≤ 20 min. |
| White |
≤ 20 min. |
| Correction time (BIII tile): |
- |
| +23 °C |
≥ 15 min. |
| Foot traffic/grouting of joints at +23 °C (Bla tile): |
- |
| Grey |
~ 20 hrs |
| White |
~ 20 hrs |
| Foot trafic/grouting of joints at +35 °C (BIa tile): |
- |
| Grey |
~ 8 hrs |
| White |
~ 8 hrs |
| Ready for use at +23 °C / +35 °C (BIa tile): |
- |
| - light foot tra c |
~ 3-2 days |
| - heavy trafic |
~ 4-3 days |
| - swimming pools (+23 °C) |
~ 14 days |
| Coverage per 5mm thickness: |
- |
| Grey |
~ 1 kg/per 1.3 sq. f. |
| White |
~ 1 kg/per 1.3 sq. f. |
| Shelf life |
- 12 months from production in the original sealed packaging, protect from humidity |
| Pack |
20 KG Bag |
Warning:
→ Product for professional use
→ abide by any standards and national regulations
→ do not use the adhesive to correct surface irregularities greater than 15 mnm
→ protect from direct rainfall for at least 24 hrs
→ the temperature, ventilation and absorption of the surface and covering materials to be fixed may cause variations in the adhesive workability and setting times
→ use the right size of toothed trowel for the format of the tile or slab
→ guarantee a full-bed in all external fixing operations
